Tropical Journal of Pharmaceutical Research Pharmacotherapy Group, Faculty of Pharmacy, University of Benin, Benin City, Nigeria ISSN: 1596-5996 EISSN: 1596-9827 Vol. 9, Num. 4, 2010, pp. 387-394

Tropical Journal of Pharmaceutical Research, Vol. 9, No. 4, July-August, 2010, pp. 387-394

Research Article

Quality control tests on Andrographis paniculata nees (family: acanthaceae) - An Indian 'Wonder' plant grown in Nigeria

Sunday J Ameh¹, Obiageri O Obodozie¹, Uford S Inyang¹, Mujitaba S Abubakar², Magaji Garba³

¹ Department of Medicinal Chemistry and Quality Control, National Institute for Pharmaceutical Research and Development (NIPRD), PMB 21, Garki, Idu Industrial Area, Abuja, Nigeria
² Department of Pharmacognosy and Drug Development, Ahmadu Bello University, Zaria, Nigeria
³ Department of Pharmaceutical and Medicinal Chemistry, Ahmadu Bello University, Zaria, Nigeria

Correspondence Address: Sunday J Ameh, Department of Medicinal Chemistry and Quality Control, National Institute for Pharmaceutical Research and Development (NIPRD), PMB 21, Garki, Idu Industrial Area, Abuja, Nigeria, sjitodo@yahoo.com

Date of Submission: 12-Jan-2010
Date of Acceptance: 11-Jun-2010

Code Number: pr10046

Abstract

Keywords: Andrographis paniculata, Quality control, Bitterness value, Physicochemical, Phytochemical, Chromatography

Introduction

The World Health Organization (WHO) ^[1] prescribed a number of quality control tests that medicinal plant materials should undergo. These can be classified into four broad areas: botanical, physiochemical, pharmacological and toxicological. The botanical embraces sensory evaluation, foreign matter, microscopy and histochemistry while the physiochemical includes loss on drying, ash values, extractive values, volatile oils and chromatography - TLC and HPLC. The pharmacological includes bitterness value, haemolytic activity, astringency or tannin content, and swelling and foaming indices. The toxicological embraces a variety of studies including: tests for arsenic and heavy metals, pesticides, aflatoxins, radioactivity, microbial contamination, and tests for specific organisms such as Salmonella.

In this study, we have determined the bitterness value of Andrographis paniculata as a key pharmacological parameter; substituted microscopy and histochemistry for classical phytochemical screening; and carried out the following physicochemical tests: loss on drying, ash, extractability and TLC. The cultivation of Andrographis paniculata in NIPRD′s botanical garden commenced in the 1990′s with seeds obtained from India. In this study we examine the dry aerial parts of the plant obtained in the Institute, using the methods prescribed by WHO ^[1] . The results obtained are discussed within the context of the Institute′s aim of developing a suitable dosage form from Andrographis paniculata - a bitter wonder plant reputed for its immunostimulant and other properties in humans ^{[2],[3],[4],[5],[6],[7]} .

Experimental

Sampling and treatment of material

The aerial parts of Andrographis paniculata, obtained during the months of September and October from the botanical garden of the National Institute for Pharmaceutical Research and Development (NIPRD), were air-dried in a well-ventilated shade, designed for drying medicinal plant materials. The materials were subsequently comminuted to coarse powder with a grinding machine. The procedure ^[1] for sampling was as follows: Three (3) original samples from each batch or container were combined into a pooled sample and subsequently used to prepare the average sample. The average sample was prepared by "quartering" the pooled sample as follows: each pooled sample was mixed thoroughly, and constituted into a square-shaped heap. The heap was then divided diagonally into 4 equal parts. Any 2 diagonally opposite parts were taken and mixed carefully. This step was repeated 2 to 4 times to obtain the required quantity of sample. Any material remaining was returned to the batch. The final samples were obtained from an average sample by quartering, as described above. This means that an average sample gave rise to 4 final samples. Each final sample was divided into 2 portions. One portion was retained as reference material, while the other was tested in duplicate or triplicate.

Determination of bitterness value

The bitterness of herbs was determined by the method described by WHO ^[1] which compares the threshold bitter concentration (TBC) of an extract of the herb with the TBC of a dilute solution of quinine hydrochloride. The bitterness value is expressed in units equivalent to the bitterness of a solution containing 1 g of quinine hydrochloride in 2000 ml. Thus, the bitterness value of the solution (1 g of quinine hydrochloride in 2000 ml of drinking water) is set at 2×10 ⁵ units. The method is identical to that described in the European Pharmacopoeia ^[8] , and used by Meyer et al ^[9] . The following provisos, based on WHO stipulation ^[1] were applied:

1. Safe drinking-water was used for extracting the aerial parts of the herb, for mouth-wash after each tasting, and for dissolution of the quinine.
2. In order to obtain an informed consent of the volunteers consisting of staff, interns and students, they were first given a seminar on the taste physiology, bitterness and the WHO method for determining bitterness. Subsequently a date for the test was agreed. It was further agreed that participants will refrain from food, drinks and medicaments an hour before the test.
3. Since sensitivity to bitterness varies greatly between persons and at different times in the same person, each participant in the test tasted both the herbal extract and the quinine solution within a short space of time.
4. All participants were first required to taste the drinking water to be used in the test and a solution of 0.058 mg of quinine hydrochloride in 10 ml of that water. Only those who sensed no bitterness in the water, but sensed bitterness in the quinine solution were included in the test.
5. The tasting each series of dilutions of the extract or quinine solution must commence with the lowest concentration in order to retain sufficient sensitivity of the taste buds.
6. All the solutions and the drinking-water for mouth washing should be at 20-25°C.
7. Since the calculation of bitterness value is based on the procedure here described, this must be followed with strictly as follows:

Preparation of standard quinine solution

Exactly 0.1 g of quinine hydrochloride was dissolved in sufficient drinking-water to produce 100 ml. Subsequently, 5 ml of this solution was diluted to 500 ml with safe drinking-water to give the stock standard solution of quinine hydrochloride labeled S _q , and contained 0.01 mg of the quinine standard/ml. Nine test-tubes labeled 1 to 9 were set up to contain 4.2, 4.4, 4.6, 4.8, 5.0, 5.2, 5.4, 5.6 and 5.8 ml of (S _q ), respectively. Into tubes 1 to 9 were then added 5.8, 5.6, 5.4, 5.2, 5.0, 4.8, 4.6, 4.4 and 4.2 ml of drinking-water, respectively. This meant tubes 1 to 9 contained 0.042, 0.044, 0.046, 0.048, 0.050, 0.052, 0.054, 0.056 and 0.058 mg of quinine hydrochloride, respectively.

Preparation and dilutions of herbal extract (test) stock solution

Exactly 1 g of the herb was extracted with drinking-water to produce 1000 ml of aqueous extract. Subsequently, 5 ml of the extract was diluted to 500 ml with drinking-water. This solution was labelled the stock extract (S _h ). It contained 0.01 mg of the herb /ml. Ten tubes labeled 1 to 10 were set up to contain 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10 ml of S _h , respectively. Into tubes 1 to 10 were then added 9, 8, 7, 6, 5, 4, 3, 2, 1 and 0 ml of drinking-water, respectively.

Procedure for the test

First, the participant rinsed his or her mouth with drinking-water, and then tasted 10 ml of the most dilute solution by swirling it in the mouth for 30 s, noting whether or not the solution tasted bitter. He or she held the solution in the mouth for another 30 s, and noted whether or not there was a loss of bitterness. Subsequently, the solution was spat out, and the mouth rinsed with drinking-water. The participant waited for 10 min before the next higher concentration was tasted. The procedure above was repeated until the dilution with TBC (that is the lowest concentration at which a solution continues to taste bitter after 30 seconds) was attained by the participant. After the first series of tasting (either with the quinine solution or the herbal extract), the mouth was rinsed thoroughly with drinking-water until no bitter sensation remained. A waiting time of 10 minutes must elapse before carrying out the second series of tasting. Bitterness value (units/g) was computed from Eq 1 ^[1] .

Bitterness value (units/g) = (2000 x C)/ (A x B) ….… (1)

where A = the concentration of the herbal stock solution (S _h) in (mg/ml), B = the volume of S _h (in ml) in the tube with the threshold bitter concentration, and C = the quantity of quinine hydrochloride (in mg) in the tube with the threshold bitter concentration.

Physicochemical tests

The following tests, briefly described, were carried out on the extracts as per WHO ^[1] .

Loss on drying (LOD)

This was carried out using a minimum of 0.5 - 1.0 g of material. Drying was effected in a Lindberg/Blue M gravity-convention oven maintained at 105-110 ⁰ C, for 3 h, after which the sample was allowed to cool to room temperature in a desiccator, and subsequently weighed. The time interval from the oven to point of weighing was usually about 30 minutes. The results are expressed as a range or as mean ± standard deviation.

Total ash (TA) and Acid insoluble ash (AIA)

These values were determined using a minimum of 0.5 - 1.0 g of material in a furnace (Vecstar Furnace) heated gradually to the ignition temperature of 650 - 700°C. The process was repeated until at least two consecutive constant weights were obtained. The results are expressed as range or mean value ± standard deviation.

Evaluation of water extractive value

About 4 g of accurately weighed coarsely powdered, air-dried sample was transferred into a glass-stoppered, 250-ml reflux conical flask, followed by the addition of 100 ml of water. The flask was weighed along with its contents, and recorded as W ₁ . The flask was well shaken, and allowed to stand for 1 h. Subsequently a reflux condenser was attached to the flask, and boiled for 1 h, cooled and weighed again. The weight was recorded as W ₂ . and then readjusted to W ₁ with water. The flask was shaken well once again and its contents rapidly filtered through a dry filter paper. By means a pipette, 25 ml of the filtrate was transferred to a previously dried and tarred glass dish and then gently evaporated to dryness on a hot plate. Subsequently, the dish was dried at 105 °C for 6 h, cooled in a desiccator for 30 min, and weighed. The water extractable matter was calculated as %w/w of the air-dried sample.

Phytochemical tests

The following tests as described by Harborne ^[10] and Onwukaeme and coworkers ^[11] were carried out on the herb or aqueous extract.

Fehling′s test for reducing sugars

To about 10 mg of the extract in test-tube was added 2 ml of water, followed by 0.2 ml of 0.1 M HCl, to effect hydrolysis of the glycosides. For the control, 0.2 ml of water was used instead of the acid. The mixture was heated in a boiling water bath to accelerate dissolution, and thern left further in the bath for 5 min. Subsequently, 1 ml each of Fehling′s solutions A and B were added while continuing to shake the mixture in the bath for 10 min. A brick-red precipitate indicated the presence of reducing sugars, formed from the hydrolysis of glycosides.

Frothing test for saponins

A pinch of the aqueous extract was added to 5 ml of water and warmed until dissolved. The solution was subsequently shaken vigorously to generate froth, and then allowed to stand. A rich froth persisting for 10 min indicates the presence of saponins.

Borntrager′s test for anthraquinone derivatives

About 100 mg of air-dried herb was extracted with 5 ml of chloroform by shaking and warming over a water bath. To about 2 ml of the supernatant, 1ml of dilute 10 %v/v ammonia solution was added, followed by shaking. A pink or red colour in the aqueous layer indicated the presence of fully oxidized anthraquinone derivatives.

Test for tannins

About 10 mg of the aqueous extract was vigorously shaken with 3 ml of warm water until dissolved. This was followed by the addition of 1 ml of 15 % ferric chloride test solution. A blue-green coloration indicated the presence of tannins.

Dragendorff′s test for alkaloids

Dragendorff′s reagent consisting of two solutions: Solution A - 1.7 g basic bismuth nitrate in 100 ml water/acetic acid (4:1), and Solution B - 40.0 g potassium iodide in 100 ml of water, was prepared. The two solutions were mixed as follows to yield 100 ml of Dragendorff′s reagent: 5 ml Solution A + 5 ml Solution B + 20 ml acetic acid + 70 ml water.. The test was carried as follows: About 20 mg of the air-dried herb was extracted with 20 ml of methanol by shaking and heating over a boiling water bath. The extract was subsequently filtered and allowed to cool. Each 2 ml of the filtrate in a test-tube was treated with 2 ml of Dragendorff′s reagent. The development of an orange-brown precipitate presumptively indicated the presence of alkaloids.

Thin layer chromatography (TLC)

Florescent, precoated plates were used for both the normal and reverse phase TLC. The normal phase utilized silica K6, and hexane: ethylacetate: methanol (4:4:1) as mobile phase while the reverse phase utilized KC18 plate, and methanol: water (80:20). Solutions of analytes were prepared and applied as follows: To 1 mg of the analyte, 2 drops of ethanol were added and mixed well (~1 %w/v solution). The plates used were 5 cm wide x 20 cm long. With a ruler and a pencil, a distance of 5 mm was measured from the bottom of the plate, and a line of origin was lightly drawn across the plate, without disturbing the adsorbent. The analyte was applied to the origin as a 1 μl droplet. The spot was allowed to dry. Subsequently, the plate was developed in a developing tank saturated with the vapour of the solvent system to be used as mobile phase. The level of the solvent in the tank was adjusted to a level 2 to 3 mm below the line of origin on the plate. The plate was considered developed when the solvent front reached a predetermined line, not less than 5 mm below the top of the plate. The air-dried plate was visualized using a viewing cabinet (Cammag) and a UV-lamp (Cammag - equipped to emit light at 254 or 366 nm). The resulting chromatogram was photographed and subsequently drawn to scale.

Results

Results from the determination of bitterness value are shown in [Table - 1], while those from the physicochemical determinations are shown in [Table - 2]. The phytochemical profile of the herb is shown in [Table - 3], while the attempt to provide TLC fingerprints for the herb is indicated in [Figure - 1]. [Table - 1] shows that that the males were more sensitive than females to the bitterness of quinine hydrochloride; the difference was significant at (p < 0.05) ^. Although the males appeared to be less sensitive to the bitterness of Andrographis paniculata, in that their mean bitterness value was lower than those of the female, the difference was not significant (p = 0.05; two-tail, 10 degrees of freedom). Notably, the mean bitterness value for both sexes was 2.86 ± 1.74 × 10 ³ . The volunteer denoted (FNx01), aged 42, had cold at the time of the experiment. If the result of this volunteer (1.30 × 10 ³ ) is set aside, the female mean value becomes 3.97 ± 1.63 ^c × 10 ³ . Similarly, if the most extreme male result (4.60 × 10 ³ ) is set aside, the male mean value becomes 1.44 ± 0.09 ^c × 10 ³ . In that scenario the sex difference denoted by ^c becomes statistically significant at p < 0.05 (two-tail, 8 degrees of freedom). Notably, results for loss in drying, ash value and extractable value obtained in this study compared well with those obtained for the Asian plant ^[12] (see [Table - 2]). [Table - 3] shows that acid hydrolysis of the test extract gave rise to reducing sugars, implying the presence of glycosides in the herb. The presence of saponins, as revealed in [Table - 3], is attested to by the foaming produced by the aqueous extract. [Table - 3] also suggest the presence of some tannins and alkaloids, but not of anthraquinones. [Figure - 1] shows that the normal phase TLC of the herb or its aqueous extract yielded 5 spots as against 6 spots by reverse TLC. Although the image is not a ′TLC fingerprints′ in atrue sense, it does, however, could be useful in identifying herb extract.

Discussion

As stated earlier, Andrographis is called a wonder plant because it is used to treat several conditions including fever, acquired immune deficiency syndrome, herpes, influenza, cancer ^[2] .

Determination of bitterness by sensation is subjective and cumbersome, and does not readily appeal to every analyst. However, determination of bitterness by taste, as in the present study, remains an appropriate method. It is well known that medicinal plant materials called "bitters" are employed therapeutically, mostly as appetizing agents. Their bitterness stimulates secretions in the gastrointestinal tract, especially of gastric juice ^[16] . As indicated under [Table - 1], the mean bitterness value for men and women was 2.86 ± 1.74 × 10 ³ units per g. This translates to about 1.43 ± 0.87 %w/w of the bitterness value of quinine hydrochloride. The wide range of the value is not unusual. For example, Meyer et al ^[9] found bitterness values of 58.1 ±110 × 10 ⁵ and 51.6 ± 156 × 10 ⁵ for praziquantel and (R)-praziquantel, respectively. The chief bitter agent in Andrographis is thought to be andrographolide, which constitutes about 2.4 %w/w of the dry herb ^[18] . [Figure - 1] is, without doubt, useful; and in combination with the physicochemical measurements shown in [Table - 2], represents a step in characterizing the Nigerian grown Andrographis. [Table - 3] shows that the herb contains reducing sugars (including probably, glycosides), saponins, tannins and alkaloids.

[Figure - 1] shows that normal phase TLC of the herb or its aqueous extract yielded 5 spots as against 6 spots yielded by reverse TLC, but the chemical character of the spots were not investigated. Either of these chromatograms may be useful in identifying the aqueous or ethanol extract of Andrographis paniculata.

Conclusion

The findings confirm some key similarities between the Nigerian and the Asian herb, as well as provide quantitative and descriptive data essential for identifying and characterizing the Nigerian grown Andrographis paniculata - an essential step in drug development. ^[19]

References

Copyright 2010 - Tropical Journal of Pharmaceutical Research

The following images related to this document are available:

Photo images